Bison Sealant Strip, 6302091, 3.35 Mtrs x 22MM, White
- Brand:
- Bison
- SKU:
- 363522158335
- Minimum Purchase:
- 1 unit
- Item Name:
- Sealant Strip
- Manufacturer:
- Bison
- Color:
- White
- Working Temperature:
- +5 to +40 Deg.C
- Coverage Area:
- 3.35 Mtrs
- Length (Mtr):
- 3.35 Mtrs
- Width:
- 22mm
- Brand Origin (not manufacture):
- United States
- Delivery Time:
- 2-7 Days
- Unit:
- Piece
Description
Adhesive sealant strip for beautiful, waterproof decorative sealing of joints along the bath, shower basin, washbasin,draining board, sink, floor and tiles. Easy to apply. Ideal for decorative applications
Suitable ForSuitable for sealing joints along the bath, shower basin, washbasin, draining board, sink, floor and tiles.
Not Suitable ForNot suitable for bitumen, polyethylene (PE), polypropylene (PP), PTFE and aquaria.
Surface requirementsThe surface must be dry, clean and free of dust, rust and grease.
Preliminary surface treatmentThoroughly clean the substrate using an abrasive and carefully remove old sealant residue (mechanically or by using a sealant remover). Please make certain that the part of the substrate to be exposed remains undamaged. Treat irregularities in the surface, such as deep tile joints, with a fine filler. Carefully degrease the substrate using methylated spirits, acetone (not suitable for plastics) or ammonia. Please note: Do not use benzine, white spirits or thinner to degrease. Make sure that the substrate is completely dry.
Directions for use1. Thoroughly clean the surface with an abrasive and remove old sealant residue. Treat irregularities, such as deep tile joints, with a fine filler. Degrease the surface with methylated spirits, acetone or ammonia (not white spirit!) and allow to dry. 2. Always start with the longest joint. Cut the sealant strip to the required length, observing 10-15 mm margin. 3. Fold the strip in half along its entire length (figure 1). For better adherence warm up application surface (tiles / bath) with the hair dryer. 4. Remove a small section of the protective film. Place the exposed part of the strip on the joint and remove the protective film. Apply the strip while firmly pressing downward (figure 2). Attention: make sure to hold the strip under an angle of 90 degrees while applying and to press firmly to create optimal and maximum contact. Do not stretch the strip as you press. 5. Cut off the excess strip at the end. 6. Make sure the strip adheres well (especially on the tile joints), then apply the other strip(s) in the same way. 7. In corners, overlap the strips. Cut the overlapping parts at an angle (45°) and remove the pieces. To finish, press the corner joint firmly again. Warm up the strip with the hair dryer immediately after fixation during 10 seconds.
AdviceIn order to prevent any condensation, it is best to heat the substrate for a moment using a hair dryer. If the strip is somewhat stiff, it can be softened by preheating it. To do so, use a hair dryer or place the strip on the radiator for a little while. This will make it easier to press down the strip. For parts with major movement and for coarse substrates, a liquid Silicone Sealant is the most suitable.
Points of attentionPlease wait 24 hours before using the sanitary facilities. Before use, make sure the strip adheres well everywhere.
Stains/ResidueRemove tape residue by blotting it with the adhesive side of a leftover sealant strip or by dissolving it with white spirits.
- Adhesive sealing strip for a permanently beautiful and waterproof joint
- Water resistant
- Self-adhesive
- Strong bonding
- Easy to apply
- Permanently bright white
- Long lifespan
- Resistant to cleaning agents
Item Name: |
Sealant Strip |
Manufacturer: |
Bison |
Color: |
White |
Working Temperature: |
+5 to +40 Deg.C |
Coverage Area: |
3.35 Mtrs |
Length (Mtr): |
3.35 Mtrs |
Width: |
22mm |
Brand Origin (not manufacture): |
United States |
Delivery Time: |
2-7 Days |
Unit: |
Piece |
Related Products
Bison
Bison
Bison
Bison
Bison
Bison
Hifazat
Bison